Transistors By INVENTO

• The 74LS83 is a high speed 4-bit fuller Adder IC with carry out feature. The IC has four independent stages of full adder circuits in a single package. It is commonly used in applications where arithmetic operations are involved.
• 4-bit Full Adder with Carry Out. Nominal Operating Voltage: 5V
• Maximum Operating Voltage: 5.5V. Output Propagation delay: 16nS.
• Maximum Input Low Voltage: 0.8V. Minimum Input High Voltage: 2V.
• Package Include 1 x 7483 IC

• The 7402 is a high speed quad 2-input NOR Gate. The device logic gates utilize silicon-gate CMOS technology to achieve operating speeds similar to LSTTL gates with the low power consumption of standard CMOS integrated circuits. This device have the ability to drive 10 LSTTL loads.
• Buffered inputs, 7ns Propagation delay, Balanced propagation delay and transition times, Significant power reduction compared to LSTTL logic ICs, 30% High noise immunity.
• Logic Family / Base Number: 74HC02, Logic Type: NOR, Output Current: 5.2mA, No. of Inputs: 2, Supply Voltage Min: 2V, Supply Voltage Max: 6V.
• No. of Pins: 14Pins, Logic IC Family: 74HC, Logic IC Base Number: 7402.
• Package Include 5 x 7402 IC

• The L7806CV is a three-terminal positive Voltage Regulator with several fixed output voltages, making it useful in a wide range of applications. This regulator can provide local on-card regulation, eliminating the distribution problems associated with single point regulation. Each type embeds internal current limiting, thermal shut-down and safe area protection, making it essentially indestructible.
• If adequate heat sinking is provided, they can deliver over 1A output current. Although designed primarily as fixed voltage regulators, these devices can be used with external components to obtain adjustable voltage and currents.
• Fixed Output Voltage Nom.: 6V; Input Voltage Min: 11V.
• Input Voltage Max: 35V; Output Current: 1.5A
• Package Include 5 x 7806 Voltage Regulator

• The CD4069UBE is a CMOS hex inverter in 14 pin DIP package. It consists of six CMOS inverter circuits. The CD4069UBE is intended for all general purpose inverter applications where medium power TTL drive and logic level conversion capabilities are not required. Typical application includes logic inversion, pulse shaping, oscillators and high input impedance amplifiers.
• Supply voltage range from 3V to 18V; Standardized symmetrical output characteristics; Maximum input current of 1?A at 18V (full package temperature range) and 100nA at 18V (25 degreeC).
• Logic Family / Base Number: CD4069; Logic Type: Inverter; Output Current: 6.8mA; No. of Inputs: 6.
• Supply Voltage: 3V - 18V; No. of Pins: 14Pins; Logic IC Family: CD4000; Logic IC Base Number: 4069.
• Package Include 4 x 4069 IC

• The CD4026BE is a CMOS Decade Counter/Divider with decoded 7-segment display outputs and display enable. The CD4026B consists of a 5-stage Johnson decade counter and an output decoder which converts the Johnson code to a 7-segment decoded output for driving one stage in a numerical display. Inputs common to both types are CLOCK, RESET & CLOCK INHIBIT, common outputs are CARRY OUT and the seven decoded outputs.
• Additional inputs and outputs for the counter include DISPLAY ENABLE input and DISPLAY ENABLE and UNGATED \"C-SEGMENT\" outputs. A high RESET signal clears the decade counter to its zero count. The counter is advanced one count at the positive clock signal transition if the CLOCK INHIBIT signal is low.
• Counter advancement via the clock line is inhibited when the CLOCK INHIBIT signal is high. The CLOCK INHIBIT signal can be used as a negative-edge clock if the clock line is held high. Antilock gating is provided on the JOHNSON counter, thus assuring proper counting sequence.
• Logic Family / Base Number: CD4026; Counter Type: Decade / Divider; Clock Frequency: 16MHz; Count Maximum: 5; No. of Pins: 16Pins; Supply Voltage: 3V - 18V; Logic IC Family: CD4000; Logic IC Base Number: 4026.
• Package Include: 2 x 4026 IC

• The CD4077BE is a quad CMOS Exclusive-NOR Gate for use with logical comparators, adders/subtractors, parity generators and checkers. The CD4077B provide the system designer with a means for direct implementation of the Exclusive-OR and Exclusive-NOR functions, respectively.
• Medium speed operation - tPHL, tPLH = 65ns (typical) at VDD=10V, CL=50pF; Maximum input current of 1?A at 18V; 10mA DC input current; Standardized symmetrical output characteristics.
• Logic Family / Base Number: CD4077; Logic Type: XNOR; Output Current: 6.8mA; No. of Inputs: 2; Supply Voltage Min: 3V.
• Supply Voltage Max: 18V; No. of Pins: 14Pins; Logic IC Family: CD4000; Logic IC Base Number: 4077
• Package Include 3 x 4077 IC

• The LM7915CT is a 3 terminal regulator requiring only one external component (compensation capacitor at the output). The LM7915CT is capable of supplying 1.5A of output current. This regulator employs internal current limiting safe area protection and thermal shutdown for protection against virtually all overload conditions.
• Low ground pin current of the LM79XX series allows output voltage to be easily boosted above the preset value with a resistor divider. The low quiescent current drain of this device with a specified maximum change with line and load ensures good regulation in the voltage boosted mode.
• Input Voltage Min: -35V; Input Voltage Max: -17.5V; Fixed Output Voltage Nom.: -15V
• Output Current: 1.5A; Dropout Voltage Vdo: 1.1V
• Package Include: 5 x 7915 Voltage Regulator

• The 74HC161D is a 4-bit presettable synchronous binary counter with asynchronous reset. This high-speed Si-gate CMOS device is pin compatible with low power Schottky TTL (LSTTL). This synchronous presettable binary counter features an internal look-ahead carry and can be used for high-speed counting. Synchronous operation is provided by having all flip-flops clocked simultaneously on the positive-going edge of the clock.
• The outputs (Q0 to Q3) of the counters may be preset to a high or low level. A low level at the parallel enable input (PE) disables the counting action and causes the data at the data inputs (D0 to D3) to be loaded into the counter on the positive-going edge of the clock (providing that the set-up and hold time requirements for PE are met). Preset takes place regardless of the levels at count enable inputs (CEP and CET). The look-ahead carry simplifies serial cascading of the counters.
• Synchronous counting and loading. Two count enable inputs for n-bit cascading. Positive-edge triggered clock. Asynchronous reset. Standard output capability.
• Counter Type: Binary; Clock Frequency: 44MHz; Count Maximum: 15; Supply Voltage : 2V - 6V; Logic IC Base Number: 74161.
• Package Include: 4 x 74161 IC

• The 74HC75D is a quad bistable Transparent Latch with complementary outputs. Two latches are simultaneously controlled by one of two active high enable inputs (LE12 and LE34). When LEnn is high, the data enters the latches and appears at the nQ outputs. The nQ outputs follow the data inputs (nD) as long as LEnn is high (transparent).
• The data on the nD inputs one set-up time prior to the high-to-low transition of the LEnn will be stored in the latches. The latched outputs remain stable as long as the LEnn is low. Inputs include clamp diodes. This enables the use of current limiting resistors to interface inputs to voltages in excess of VCC.
• Complementary Q and Q outputs; VCC and GND on the center pins; Low-power dissipation; Supply Voltage Min: 2V; Supply Voltage Max: 6V; No. of Bits: 4bit; Logic IC Family: 74HC.
• Logic Family / Base Number: 74HC75; Latch Type: Transparent; IC Output Type: Complementary; Propagation Delay: 11nsOutput Current: 5.2mA; No. of Pins: 16Pins.
• Package Include 2 x 7475 IC

• Logic Family / Base Number: 74HCT30; Logic Type: NAND
• Output Current: 4mA; No. of Inputs: 8
• Supply Voltage Min: 4.5V; Supply Voltage Max: 5.5V
• No. of Pins: 14Pins; Logic IC Base Number: 7430.
• Package Include 4 x 7430 IC

• The 4511 IC is a CMOS BCD-to-7-segment LED Latch Decoder Driver constructed with CMOS logic and NPN bipolar transistor output devices on a single monolithic structure. It combines the low quiescent power dissipation and high noise immunity features of RCA CMOS with n-p-n bipolar output transistors capable of sourcing up to 25mA. This capability allows the CD4511B types to drive LED's and other displays directly.
• Lamp Test (LT\\), Blanking (BL\\) and Latch Enable or Strobe inputs are provided to test the display, shut off or intensity-modulate it and store or strobe a BCD code, respectively. Several different signals may be multiplexed and displayed when external multiplexing circuitry is used. Input latches for BCD Code storage. Lamp test and blanking capability. Up to 25mA High-output-sourcing capability. 7-segment Outputs blanked for BCD input codes >1001.
• Logic Family / Base Number: CD4511; Logic Type: BCD to 7 Segment Decoder / Driver / Latch; No. of Outputs: 7 Outputs
• No. of Pins: 16 Pins; Supply Voltage: 3V - 18V; Logic IC Base Number: 4511
• Package Include: 2 x 4511 IC

• Logic Family / Base Number: 74HCT14; Logic Type: Inverter Schmitt Trigger.
• Output Current: 4mA; No. of Inputs: 1.
• Supply Voltage Min: 4.5V; Supply Voltage Max: 5.5V.
• No. of Pins: 14Pins; Logic IC Family: 74HCT; Logic IC Base Number: 7414.
• Package Include 4 x 7414 IC

• The SN74HC21N is a dual 4-input Positive-AND Gate. This device perform the Boolean function Y = A B C D or Y = (A + B + C + D) in positive logic. The device operates at voltage range of 2 to 6V and outputs can drive up to 10 LSTTL loads.
• 20?A Maximum ICC low power consumption; 11ns Typical tpd; 4mA Output drive at 5V; 1?A Maximum low input current.
• Logic Family / Base Number: 74HC21; Logic Type: AND; Output Current: 5.2mA; No. of Inputs: 4; Supply Voltage Min: 2V.
• Supply Voltage Max: 6V; No. of Pins: 14Pins; Logic IC Family: 74HC; Logic IC Base Number: 7421.
• Package Include 4 x 7421 IC

• The NJM4558/4559 integrated circuit are a dual high-gain operational amplifier internally compensated and constructed on a single silicon chip using an advanced epitaxial process.
• Combining the features of the NJM741 with the close parameter matching and tracking of a dual device on a monolithic chip results in unique performance characteristics. Excellent channel seperation allow the use of the dual device in single NJM741 operational amplifier applications providing density. It is especially well suited for applications in differential-in, differential-out as well as in potentiometric amplifiers and where gain and phase matched channels are mandatory.
• Operating Voltage: 4V - 18V; High Voltage Gain: 100dB.
• High Imput Resistance: 5M Ohm; Bipolar Technology
• Package Include 2 x JRC4558

• The SN74LS90N is a Decade Counter contains four master-slave flip-flops and additional gating to provide a divide-by-two counter and a three-stage binary counter for which the count cycle length is divide-by-five for the '90A and 'LS90, divide-by-six for the '92A and 'LS92 and the divide-by eight for the '93A and 'LS93. All of these counters have a gated zero reset and the '90A and 'LS90 also have gated set-to-nine inputs for use in BCD nine's complement applications.
• To use their maximum count length (decade, divide-by-twelve or four-bit binary) of these counters, the CKB input is connected to the QA output. The input count pulses are applied to CKA input and the outputs are as described in the appropriate function table. A symmetrical divide-by-ten count can be obtained from the '90A or 'LS90 counters by connecting the QD output to the CKA input and applying the input count to the CKB input which gives a divide-by-ten square wave at output QA.
• Logic Family / Base Number: 74LS90; Counter Type: Decade; Clock Frequency: 42MHz; Count Maximum: 9; No. of Pins: 14Pins.
• Supply Voltage Min: 4.75V; Supply Voltage Max: 5.25V; Logic IC Family: 74LS; Logic IC Base Number: 7490.
• Package Include 2 x 7490 IC

• The SN74LS47N is a BCD-to-Seven-segment Decoder/Driver features active-low outputs, designed for driving, common-anode LEDs or incandescent indicators directly. The IC for driving lamp buffers or common-cathode LEDs. All of the circuits except LS49 have full ripple-blanking input/output controls and a lamp test input. Display patterns for BCD input counts above 9 are unique symbols to authenticate input conditions.
• Its circuits incorporate automatic leading and/or trailing-edge zero-blanking control (RBI and RBO). Lamp test (LT/) of these types may be performed at any time when the BI/RBO node is at a high level. All types (including the '49 and 'LS49) contain an overriding blanking input (BI), which can be used to control the lamp intensity by pulsing or to inhibit the outputs. Inputs and outputs are entirely compatible for use with TTL logic outputs.
• Open-collector Outputs Drive Indicators Directly; Lamp-test Provision.
• Leading/Trailing Zero Suppression; All Circuit Types Feature Lamp Intensity Modulation Capability
• Package Include 2 x SN74LS47N