Electrical Components - Electrical Diodes

• High quality bridge rectifiers used for conversion of an alternating current input into a direct current output
• There are total 10 pieces of bridge rectifiers in this set that you may use for many projects
• The top and internal part are well welded which ensures a more stable performance
• Base is small and has a large over-current capacity, good heat dissipation and low voltage drop
• These high power, high frequency bridge rectifiers are widely used for power supply

• The Photodiode Sensor and Photosensitive Sensor Module are useful for light intensity detection and can effectively sense the light source in front of the sensor which are more suitable for searching for light.
• Photodiode Sensor :Suitable Voltage: 3.5V-5.5V;Pin Amount : 4;Overall Size: 31 x 14mm (L*W);Fixed Hole Dia: 3mm;Photoresistor Sensor Module Suitable Voltage: 3.3V-5V;Pin Amount : 4;Overall Size: 31 x 14mm (L*W);Fixed Hole Dia: 3mm;Output Format : DO digital switching outputs (0 and 1) and AO analog voltage output;In the package of: 1 Set - 1 x Photodiode Sensor and 1 x Photoresistor Sensor Module
• Photodiode Sensor is the most sensitive to ambient light intensity comparing with other sensors, which has better sense of direction and can search light in a certain direction.Photoresistor Sensor Module's sensitivity can be adjust by the blue digital potentiometer.
• It takes a short time to connect the wires correctly, as long as you use the correct working voltage.
• Please use the correct voltage for assembly and use the correct connection.

• Diode Configuration: Single; Zener Type: General Purpose; Mounting Type: Surface Mount
• Forward Voltage: 1V; Zener Voltage: 8.2V; Power Dissipation: 500mW; Package-Type: SOD-123
• Zener Voltage Tolerance: 2.5%; Zener Impedance: 8; Reverse Leakage Current: 100nA; Dimensions: 2.85 x 1.7 x 1.35mm
• Applications Include:- General Purpose etc
• Packaged by:- Sharvi Technologies (OPC) Pvt. Ltd.; Address:- #09, CK Nagar, AECS layout, Hosa Road, Bangalore-560100

• Lens: 5mm Diameter / Black / Round
• Power: 0.15 W; Receiving Angle: 40 degrees; Maximum power: 70 mw; Maximum forward current: 30 ma
• Voltage (VF) : 1.1-1.4 V; Wave long (WD) : 940 nm;
• Note:The infrared receiver has black lens, when the power supply to it, can not see the light as it is a receiver.
• Package Include 50 x IR LED

• Product Range : TRANSZORB 1.5KE Series
• TVS Polarity : Bidirectional
• Reverse Stand-Off Voltage Vrwm : 18.8V
• Clamping Voltage Vc Max : 30.6V
• Diode Case Style : DO-201

• 1. Durable and practical,portable,very convenient to install and repair
• 5.Output DC current is 100A.Maximum valuee voltage is up to 1,600V. Isolated mounting base, High reliability by unique glass passivation
• 2. Welding structure,excellent power cycling and temperature features
• 3. Can be used to PWM inverter electric current input,battery charging,etc
• 4.Power Diode Module MDS-100A is designed for three phase full rectification, which has six diodes connected in a three phase bridge configuration

• [Bridge Rectifier] --- High quality bridge rectifiers used for conversion of an alternating current input into a direct current output.
• [Stable Performance] --- Well welded structure with good temperature and power cycle ability ensures a more stable performance.
• [Current 100A] --- Designed for single phase rectification, output DC current is 100A.
• [High Quality] --- The rectifier has a large over-current capacity, good heat dissipation and low voltage drop.
• [Wide Used] --- This high power bridge rectifier can be widely used for power supply.

• Use ATmega 8, ATmega 168 or ATmega 328 microcontrollers. 2x16 character LCD display shows the result
• Built-in self-check function and optional 50Hz signal check the clock frequency accuracy and wait for calling (ATmega168 and ATmega328)
• Support automatic power off. ATmega168 or ATmega328 with 1.05k version software uses sleep mode to reduce power consumption when there is no measurement
• Only one measurement is needed to find out the connection of the full bridge. The test time is about two seconds, only capacitance and inductance measurements will take a long time
• Can set the number of measurements before the power is automatically turned off, with one - key operation, automatically turn off the power

• Features low heat, energy saving, low power consumption and long service life
• Best replacement to traditional light sources, dependable to use
• LED diode produce bright LED lights, ideal for color displays, indicators, diagnostic or analytical devices, etc
• There are red, yellow, blue, green and white 5 colors
• It can be used as lighting, flashlights, toys and gifts, car accessories, light box advertising, signal indicator, etc

• 1. Uz - stable voltage It refers to the stable voltage value generated at both ends when the voltage stabilizer passes the rated current.
• 2. Iz - rated current It refers to the current value passing through the regulator when it generates a stable voltage.
• 3. Rz - dynamic resistance It refers to the ratio of voltage change and current change at both ends of the voltage stabilizer.
• 4. Pz - rated power consumption It is determined by the allowable temperature rise of the chip, and its value is the product of the stable voltage Vz and the allowable maximum current Izm
• 5 ?--- temperature coefficient If the temperature of the stabilizer tube changes, its stable voltage will also change slightly. The relative change of the voltage at both ends of the tube caused by the temperature change of 1 is the temperature coefficient (unit:%/).